
Take two real products. A 3/8 x 6-inch steel nut eyebolt from National Hardware carries a 160-lb safe working load, yet its listing prohibits overhead lifting. A Crosby S-279 machinery eyebolt in 1/2-13 UNC carries a 2,600-lb in-line working load limit and is built for rigging.
This guide covers general-purpose eye bolts and lifting hardware, and separates rated lifting components from light-duty eye screws and bent-wire products. You'll learn the main types, how to read the specs, and how to choose by load direction, installation, and environment.
Key Takeaways
- Select by application, installation method, load direction, and manufacturer-rated capacity.
- Plain patterns suit in-line loads; shoulder patterns need proper seating and manufacturer angular guidance.
- Thread size alone isn't enough: check shank length, eye size, material, finish, and rating.
- Never assume a screw eye or unrated eyebolt can lift overhead.
What Is an Eyebolt?
An eyebolt is an externally threaded shank with a closed eye fixed at one end. The eye takes rope, cable, chain, slings, or other hardware. Some designs add a shoulder, a washer-like bearing platform below the eye that spreads load and reduces shank stress, according to Huyett's guidance.
Related parts are easy to confuse:
- Eye nuts have an internal thread and fit onto an existing threaded shank.
- Hoist rings use a pivoting or swiveling assembly instead of a fixed eye.
- Lifting lugs are typically welded or machined attachment points.
- Bolts with a bent loop are formed hardware, not engineered lifting eyes.
The same term covers machinery attachment, tie-downs, anchoring, light-duty securing, and engineered lifting. Read the product description and rating before use.
Eyebolt Types and Their Applications
Nut, Machinery, and Screw Eyebolts
- Nut eyebolts pass through a hole and are retained by a washer and nut on the far side.
- Machinery eyebolts thread into a tapped hole made to receive the shank.
- Screw eyes (lag eyes) have a pointed, tapered shank with coarse threads that cut into a pilot hole for light-duty securing. Huyett states they are not rated for overhead lifting unless the manufacturer says so.
The receiving material decides the style. Through-holes in steel call for a nut pattern, tapped machine components call for machinery eyebolts, and wood calls for a screw eye.
Plain and Shoulder Patterns
Plain (regular) patterns lack the reinforced shoulder and are meant for loads in line with the shank. Crosby prohibits regular nut eyebolts in angular lifts.
A shoulder helps resist bending, but only when it sits flush and tight against the load surface. Crosby's warning sheet shows how steep the penalty for angles is, measured from in-line:
| Angle from in-line | Adjusted WLL (% of rated) |
|---|---|
| 5° | 100% |
| 15° | 80% |
| 30° | 65% |
| 45° | 30% |
| 90° | 25% |

These are Crosby's values for its forged eyebolts. They are not universal. Use the chart from the manufacturer of the part in your hand.
Forged, Bent, and Welded Eyes
- Forged eyes are shaped from solid steel and heat treated. Crosby's S-279 is forged, quenched, and tempered.
- Bent or wire-formed eyes are made from wire, sometimes with an open gap. Huyett says these are not suited for lifting or rigging.
- Welded eyes are closed by resistance welding. Chicago Hardware describes turned eyes from low-carbon cold-drawn wire.
Appearance doesn't tell you the process. Confirm it in the manufacturer's technical documentation.
Choosing by Application
Typical use groups include:
- Lifting and rigging
- Equipment attachment
- Tie-down and transport
- Marine or outdoor securing
- Light household or facility use
A bolt can suit one group and fail in another even when thread and shape match.
Use this sequence:
- Identify the load and environment.
- Decide whether the load is in line or angular.
- Identify the receiving structure.
- Match the product's documented rating and installation instructions.
Eyebolt Specifications: How to Read a Drawing or Datasheet
Thread Specifications
U.S. inch threads follow ASME B1.1. A "1/4 x 20" callout means a 1/4-inch major diameter with 20 threads per inch, per Essentra.
Unified National Coarse (UNC) has fewer threads per inch than Fine (UNF) at the same diameter. Crosby's S-279 example is 1/2-13 UNC.
Metric works differently: M6 x 1 means 6 mm diameter and 1 mm pitch.
- Confirm inch or metric before ordering.
- Match the thread to the hole, nut, or insert.
- Check thread length and condition.
- Follow the maker's engagement guidance.
Ken Forging, for example, calls for full shank engagement on plain patterns and allows a half turn for eye alignment. That is one manufacturer's rule, not a universal one.
Dimensional Specifications
Request or confirm:
- Overall length and threaded shank length
- Eye outside diameter, inside diameter, and thickness
- Shoulder diameter and height
The eye's inside diameter must accept the sling, hook, shackle, or cable without forcing or side-loading. For OEM assemblies, fixtures, trailers, or agricultural machines, get a drawing with tolerances.
Load Rating and Working Load Limit
Working load limit (WLL) is the maximum working load the manufacturer designates. Suncor defines it as breaking load divided by a safety factor.
Crosby lists a 5:1 design factor and a maximum proof load of 2 x WLL for the S-279. That figure is a maximum proof load, not a promise every piece was individually tested.
Capacity depends on size, material, process, thread engagement, orientation, and sling angle. Use the current manufacturer load chart or certification. Never estimate capacity from diameter.
Standards, Markings, and Documentation
| Document | What it covers |
|---|---|
| ASME B18.15-2025 | Dimensions and capacities for forged carbon-steel (1/4 to 2-1/2 in.) and stainless (1/4 to 1-1/2 in.) eyebolts |
| ASME B30.26-2026 | Construction, installation, operation, inspection, and maintenance of detachable rigging hardware |
| OSHA 1926.251 | Construction rigging: daily inspection, defective-gear removal, manufacturer SWL markings |
| OSHA 1910.184 | General-industry slings (not an eyebolt dimension spec) |
In short, B18.15 governs the product and B30.26 governs its use. OSHA ties identification and safe working load to manufacturer prescriptions.
Standards do not apply identically to every eyebolt, so reconcile them with the maker's instructions. Check the current ASME text for clause-level marking and removal rules.
Markings vary. Crosby describes a name, a product identification code supporting traceability, and either size or WLL. Don't assume WLL is stamped on every eye.
Environmental and Service Specifications
Confirm material, coating, temperature exposure, chemical contact, and wear before ordering. An indoor-machinery part may corrode quickly outdoors, in washdown, or near salt.
Materials and Manufacturing Methods
Steel, Stainless, Galvanized, and Alloy Options
- Carbon steel: Ken Forging lists tensile strength of 65,000 to 90,000 psi and minimum yield of 30,000 psi. Those are material properties, not WLL.
- Alloy steel: 8620 alloy is common in shoulder and plain eyebolt families.
- Stainless: Rolled Alloys notes 316's molybdenum improves chloride pitting resistance over 304, with similar mechanical performance.
- Zinc plated vs. hot-dip galvanized: The American Galvanizers Association describes plating as thinner, suited to indoor or mild exterior service, while hot-dip coatings are thicker and last longer.
Stainless doesn't mean lift-rated. Ken's 316 shoulder nut eyebolts list a capacity column yet are not rated or recommended for any lifting. Meanwhile, ASME B18.15 includes forged stainless lifting eyebolts. Check the exact product.

Manufacturing Quality and Inspection
Forging, bending, welding, heat treatment, machining, and finishing all shape geometry and performance. For production or safety-critical lifting, confirm inspection records, traceability, proof testing, and certification. Ken Forging makes its eyebolts to ASME B18.15 and tests them to ASTM A489.
Matching Material to Environment
- Heavy equipment and agricultural machinery: Prioritize rated forged steel with a durable finish for vibration and mud.
- Outdoor, marine, or washdown: Hot-dip galvanized or 316 stainless, after verifying the rating.
- Indoor plants: Plain zinc plating is often enough.
Corrosion resistance never replaces load verification, fit, inspection, or correct installation.
How to Select and Use the Right Eyebolt Safely
Start with the Application and Load Path
Decide whether the eyebolt will lift, pull, secure, anchor, or position. Account for shock, vibration, and dynamic loading. Then determine whether force stays in line with the shank or goes angular, lateral, or off-plane. If it doesn't stay in line, choose a purpose-designed alternative such as a hoist ring.
The eyebolt's rating must also fit the whole system: slings, shackles, hooks, and the supporting structure.
Confirm Installation and Seating
- Follow the instructions for the hole, nut, washer, and contact surface.
- Crosby calls for the shoulder flush and tight against the load, with no undercutting to get seating. On nut patterns, leave enough shank for full nut engagement.
- Load in the plane of the eye.
- Don't weld, bend, grind, or modify a rated eyebolt without an approved engineered procedure.
Inspect Before Use and During Service
Check for these defects before each use and during service:
- Bending, deformation, cracks, nicks, or gouges
- Thread damage, corrosion, or heat or weld damage
- A distorted eye
- Missing or illegible markings
I&I Sling's guidance says to remove eyebolts for bending, distortion, stripped threads, or unreadable identification. Destroy bent, elongated, worn, or altered eyebolts and never repair a stressed one.
Set inspection frequency by the applicable standard, manufacturer instructions, and your site safety program.
Avoid Common Selection Errors
- Choosing by nominal diameter alone
- Using a plain eyebolt for an angular lift
- Using an unrated screw eye overhead
- Assuming a bigger eye means higher capacity
Get the drawing, load data, installation instructions, and material documentation before approving a substitute.
Custom Bent Fasteners from Ottawa Products Co.
Ottawa Products Co. manufactures OEM bent bolts, exhaust clamps, hangers, and related components for heavy-duty, agricultural, automotive, and industrial markets in Curtice, Ohio. It is not a standard eyebolt supplier. When you need a custom bent fastener or formed component instead, its custom bent bolts cover U-bolts, J-bolts, hook bolts, V-bolts, anchor bolts, and stud bolts from 1/4" through 1/2", with no minimum order. Contact the quoting or engineering team at quotes@ottawaproducts.com for an application review.
Frequently Asked Questions
What is an eyebolt used for?
Attaching, lifting, pulling, anchoring, and securing. Whether a given eyebolt suits a job depends on its rating and intended use.
What is the difference between a plain eyebolt and a shoulder eyebolt?
A shoulder eyebolt has a bearing platform below the eye that helps resist bending. Plain patterns are generally limited to in-line loads; shoulder patterns may allow approved angular use when seated properly.
Can plain eyebolts be used for angular loads?
Don't assume so. Crosby prohibits regular nut eyebolts for angular lifts. Follow the manufacturer's instructions or choose an engineered alternative.
How are eyebolts measured?
By thread diameter and pitch, shank length, eye inside and outside diameter, eye thickness, and shoulder dimensions where present.
What does the working load limit of an eyebolt mean?
It's the manufacturer-designated maximum working load for a specified configuration and conditions. It is well below the breaking load.
Are screw eye bolts suitable for overhead lifting?
No, unless the product is specifically documented and approved for that lift. Light-duty screw eyes are not rated lifting eyebolts.